NOKIA | Ericesson | Motorola | Seimence |
Tips For SIEMENES |
These SIEMENES codes
will work on most Nokia Mobile Phones, however we
accept no responsibility of any kind for damage done to your phone
whilst trying these codes. Siemens S25/C25 SP unlock *#0003*(secret code 8 digits)# Show IMEI code: * # 06 # Resets language to automatic selection : * # 0000 # then Green button Pin Out Data Cable schematics Phone's connector pin-out: 1- GND 2- SB 3- POWER 4- NC 5- TX 6- RX 7- CLOCK 8- DATA 9- GND MIC 10- HF MIC 11- AUDIO 12- GND AUDIO Siemens S1/S3/S3 Com To view the software date and else with S3 com, S4, S4Power, Sony cmdx 1000e press with SIM removed *#06# and left softkey. To view some other stuff with S4Power, Sony cmdx 1000e press with SIM removed *#06# and left softkey twice. To view the software date with S3 com, S4, S4Power, Sony cmdx 1000e press with SIM installed menu 98 and left softkey twice. ACTIVATE MONITOR MODE Siemens S1/S3 Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key), 5553756, Hang-Up Button (Red Handset key) Siemens S3 COM/S4 Menu, 9 (Phone Options), 7 (Phone Status - 8 on Some), Left Display Button (left MENU key), 7684666, Hang-Up Button (Red Handset key) Note: Now Monitor should appear at the bottom of the Network Options menu. MONITOR MODE Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress ) CH Channel Number RX Signal Strength (dB) N NCC (Colour Code) B BCC (Colour Code) CI Cell ID (in Hex) C1+ How long before phone does forced hand over. (see RX and RXAM) LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC TXPWR Transmit Power (dB) RXAM Receive signal strength cut-off point TS* Time Slot Number TA* Timing Advance. Distance from tower in Km X 2 PL* Power Level POWER table PL: 5 6 7 8 9 10 11 12 13 14 15 dB: 33 31 29 27 25 23 21 19 17 15 13 Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02 LF* C1 value with continuous transmission from tower LS* C1 Value with discontinuous transmission from tower QF* Bit Error Rate with continuous transmission from tower QS* Bit Error Rate with discontinuous transmission from tower BER (bit error rate) table QF/QS register: 0 1 2 3 4 5 6 7 % of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6 Siemens S1/S3 Here's a trick to play Tetris, also known as Klotz on a Siemens S1. Turn the phone on. Enter PIN. Before the telephone has logged in to the your GSM net do the following steps. 1: Choose F 9 (function settings) 2: Choose send own number and push the right button for choose. 3: Push 9 USE 2 as < and 8 as > , rotate the klotz with 5 and drop with 4. [I have just heard from one of the programmers of the phone that Tetris was in the phone during development, but it was removed before it was produced. Apparently someone has the patent on games in mobile phones and Siemens didn't want to pay the licensing fees. It was either in Menu F-9-9 or it's not there at all.] Siemens S3 Comfort MONITOR MODE The Siemens S3 Com series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone. TO ACTIVATE MONITOR MODE: Turn the phone on. Enter the PIN access code on press OK. (Only if is enabled). Press Menu. (Left top button). Press 9. (Phone Options). Press 8. (Phone Status) (May be button 7 in some phones). You may see your IMEI Number Left Display Button (Top left MENU key). 7684666 Hang-Up Button. (Red Handset key). Note: Monitor should appear now at the bottom of the Network Options menu. MONITOR MODE Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes Siemens S4/S4 Power In phonebook under "Own Phone No." enter +12022243121 (which is the number to the White House) and you'll get a greeting from the people who programmed the phone. MONITOR MODE The Siemens S4 series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone. TO ACTIVATE MONITOR MODE: Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key), 7684666, Hang-Up Button (Red Handset key) Now "Monitor" should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress ) -------------------- CH Channel Number RX Signal Strength (dB) N NCC (Color Code) B BCC (Color Code) CI Cell ID (in Hex) C1+ how long before phone does forced hand over. (see RX and RXAM) LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC TXPWR Transmit Power (dB) RXAM Reeceive signal strength cut-off point TS* Time Slot Number TA* Timing Advance. Distance from tower in Km X 2 PL* Power Level Power Table PL: 5 6 7 8 9 10 11 12 13 14 15 dB: 33 31 29 27 25 23 21 19 17 15 13 Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02 LF* C1 value with continuous transmission from tower LS* C1 Value with discontinuous transmission from tower QF* Bit Error Rate with continuous transmission from tower QS* Bit Error Rate with discontinuous transmission from tower BER (bit error rate) table QF/QS register: 0 1 2 3 4 5 6 7 % of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6 Siemens S6/S10 In Phonebook, store as your own number: +12022243121 Then you get the sun and two palms in the display, also a greeting message of the "MMI-team". It has been said that the phone number is the number of the Capitol building in Washington, DC (but not sure). Siemens S15 Secret Menu's Press * -> # -> 7 -> 4 -> 3 -> 6 -> 3 -> 6 -> 7 -> * -> 8 -> 3 -> 7 -> 8 -> # ,press clear key to clear screen and return to stand-by mode press Menu, it will show additional menu Menu 3.3.4 Band selection, Menu 3.3.4.1 Automatic band selection, Menu 3.3.4.2 select GSM 900 only, Menu 3.3.4.3 select GSM 1800 only, Menu 10 Engineering, Menu 10.1 MS info, Menu 10.2 software detail, Menu 10.2.1 software version, Menu 10.2.2 EEPROM version, Menu 10.3 Test/production details Menu 10.3.1 Hardware deta Menu 10.3.2 production deta Menu 10.3.3 Service deta Menu 10.3.4 Mechanical deta Menu 10.1.1 MS info on, then on the screen show these, for example: FCN RXL C1 C2 642 011+11+91 -> PAGE 1 CID DSC CB 11211 045 000 -> PAGE 2 BCC NCC TN 000 002 00 -> PAGE 3 RXf RXs RQf RQs 00 00 00 00 -> PAGE 4 ATa APa Hn Hf 001 000 05 00 -> PAGE 5 DTU DTD HP CI + ? - - -> PAGE 6 MM CC RR IdNS Nul Idl -> PAGE 7
|