By John Thawley*
We would be the first to point out that, in this day and age of high-performance
engines flowing from automotive machine shops and factories alike, you cannot
build up an old Y-block Ford to be a world-beater. Nevertheless, thousands are
still in service in trucks and passenger cars in this country, while in much of
South America and Australia the Y-block Ford (or Mercury) is the engine for
street and circle track, due to availability and low cost. This same
availability and low cost makes the engine somewhat attractive to the Stateside
budget rodder. For instance, in Los Angeles a ball-park price for a complete
Y-block in running condition is $25. Granted, this is little more than a core to
rebuild from, but not bad.
We'll point out some combinations of parts, what to look for in wrecking yards,
what can be had in speed equipment and some dos and don'ts on assembly, and then
let you take it.
Stick with the 272, 292 or 312 block assembly. In 1954 (the first year of the
Y-block), Ford introduced the engine with 239 cubic inches. Camshaft bearings
are of different sizes than the later blocks, and a number of other components
won't interchange, so it is best to forget this engine and go directly to the
larger block.
The charts included in this article show how the engine began life in a relative
stage of untune, worked up the horsepower ladder to a peak in 1957, and then was
detuned by the factory in subsequent years. This is your first clue to finding
the road to low-cost performance. You're now looking for '57 Fords, right?
The assembly line Y-block Ford contains more meat than a prizewinning Hereford.
The lower block skirt extends well below the centerline of the crankshaft to
ensure rigidity for the five main bearing saddles. The 272 block can be bored
out to 292, the 292 goes out to 312 with no trouble and, since replacement
pistons for the 312 are sold in .40-inch oversize, that route may be taken for
increased displacement. All of this is safe and presents no problem. Unless one
encounters a core shift problem, much more can be done with a boring bar. We
currently have a Y-block running on the street which began life as a 272 and is
now .030-inch over the 312 bore of 3.800. This is not uncommon. So if your
desire is displacement, don't shy away from the boring bar. Anything over 3.875
is asking for trouble.
A check of the chart shows the same stroke for the 272 and 292 versions. The
two-year offering of the 312 produced a longer stroke (by .140 inch). What the
chart doesn't show is that the 312 crank turned on 1/8-inch-larger-diameter main
journals. To use this crank in the 272-292 block, the main journals must be
machined down to the smaller size. If this is done, the 312 connecting rods must
be used. Depending on what bore you've decided on, the 272, 292 or 312 pistons
may be used. If the 272 or 292 pistons are used in this configuration, the
entire assembly should be balanced, since the 312 pistons were 2 ounces heavier
than the late 292 pistons.
Block preparation past boring and honing to fit the pistons should include hot
tanking. Before boiling out, the baffle plate bolted to the block at the oil
filter boss should be removed, since sludge collects here and is hidden from
view. After hot tanking and machining, scrub the block with brushes and hot
soapy water.
In the crankshaft department, the forged steel truck unit is worth searching
for, since it was designed to withstand more loading than the cast units. The
parts number on this item is listed as C1TE6303F. The number to look for on the
crank is the same except for a B which replaced the F at the end of the parts
number. If you plan to spend the better (or worse) part of a Saturday in a
wrecking yard pulling a crank from a truck, make a deal for the rods also. The
truck rod (parts No. C1TE6200C) is somewhat beefier and better-designed than the
passenger car counterpart.
The rods should not be mixed in the assembly; that is, use all truck rods or all
passenger car rods, not three of one kind and five of another. Also, you'll be
miles ahead of the game if the piston, rod and crank assembly is balanced after
you've decided what you want.
There are at least 17 different head casting marks from 1955 to '62. Compression
ratio varies, since in several cases a particular type head was used on the
272-, 292- and 312-inch engines produced in a given year. The expeditious route
out of this dilemma is a set of '57 heads. Check the chart for casting numbers,
parts numbers and compression ratio per given displacement. Note also that the
'57 heads carried the large 1.925-inch intake valve and a rocker ratio of 1.54.
Any of the heads can be helped to some extent by some judicious grinding in the
combustion chamber, where the high lip shrouds the valve and thus disrupts the
flow. With machinists' bluing, a head gasket and a scribe, mark off how far
outward you may grind before botching up a set of heads. Enlarging the intake
and exhaust ports with a grinder will help flow characteristics somewhat.
A good valve job (not a $12.95 special) with a close check for excessive
clearances in the guides -- and the lower portion of the heads is taken care of.
One of the chronic problems with the Y-block is a lack of lubrication in the
upper valve train assembly. There are a number of ways to help overcome this
malady; none are sure cures. Enlarge the oil entrance hole in the head (check
the photos). Make certain that the rocker shafts exhibit no trace of scoring; if
they do, replace them. There are several oil holes in the side of the rocker
shafts. These must line up with the holes in the rocker shaft support brackets.
Change oil and filters often in these engines to slow down the formation of
sludge.
The '57 cam produces more lift and slightly longer duration than any other
FoMoCo cam except the unit designated for use with the supercharger. This cam is
all but impossible to locate. The enthusiast who wants this much camshaft would
be time (and probably money) ahead to go to any number of the racing cam
grinders -- such as Isky, Crower or Crane -- who still offer such grinds for the
Y-block. For street use, shoot for a cam with relatively short duration but
higher-than-stock lift. This configuration tends to retain bottom end torque,
and a cam of less than 270 degrees duration seems to work quite well with any of
the intake manifold/carb combinations.
Spending the time necessary to come up with a set of '57-'59 heads will pay off
in the manifolding department, since the single four-barrel and the two-barrel
manifold of these years have larger runners which match up with the '57-'59
heads. Later heads and intake manifolds exhibited ports of smaller size. For a
brief period of time Ford offered a dual four-barrel intake manifold, as did a
number of speed equipment makers. Even if the item can be located, this is still
not the manifold to have for all-around performance. A somewhat
archaic-appearing three two-barrel manifold by Edelbrock has proven time and
again that it offers the response, flow and flexibility desired for street
flogging or highway cruising. The manifold is most often set up with Holley
two-barrels pirated from boneyard '56 Fords. After the three two-barrel manifold
and carb combination, the next best unit is probably the stock four-barrel
manifold mounted with a late Holley or Autolite carb. Depending on carb used,
the intake manifold may have to be touched with a grinder to allow the larger
throttle plates to open into the manifold throat.
The dual exhaust manifolds offered on the '57 312 engine were the best
factory-produced items for this engine. They'll bolt to all of the Y-blocks. At
one time, a lot of header systems were available. Currently, Hedman is probably
the only manufacturer to produce a header system in any volume for the Y-block.
Carefully rebuilt to factory clearances with quality parts (our own engine went
together with TRW bearings and pistons, Grant rings, etc.), the Y-block will
offer countless miles of service. This may not be the most powerful engine
available to the low-budget rodder, but it is one of the lowest in cost -- both
important features to one just getting started with engines.
*HOT ROD MAGAZINE, September 1968