Tippmann 98/98 custom and on bottom Tippmann A-5

The 32 degrees tippmann 98 rear cocking system. Turns the tippmann into a rear cocking gun rather than the side cocking system that comes stock on the tippy's. It goes on the back of the gun.

The 32 degrees twisted spiral rear velocity adjuster. Eliminates the allen key velocity screw to a turning knob that goes on the back of the gun below the bolt cap. Also looks great on tippy's.

The tippman 98 rocket cock. This goes over the side cocking system and keeps the dirt out of the gun. It also hooks onto the side cock and all you have to do to cock the gun is to pull the rod back

The tippmann 98 custom pneaumatic electrnic kit. This electro kit unlike the sear stripper kit uses the a mechanized type ram. When the trigger is pulled the ram is fired but instead of having to let the trigger go foward again the trigger can stay pulled and the gun will still fire.This electro kit has multiple modes including full auto. This is a more basic system to understand but it will put alot more wear and tear on a tippmann than the sear stripper kit.

This is the tippmann 98 custom sear stripper electro kit. This electro can also make a shorter trigger pull on a tippmann possible because it uses the valves to open and close. This is a much more efficent type of elctro and is probabally more worrth buying. Has the multiple modes.

This is the same thing as the pneumatic electro kit excpet it is made for the regular tippmann, not the 98 custom. Works the same way and has adjustable modes. This is simply the e-bolt for the regular tippmann.

Tippmann 98 starfire bolt. This is an aftermarket bolt made by tippmann, it is not an open face bolt making it much more consistent and accurate. Great aftermarket bolt to invest in for a tippmann.

The tippmann 98 vertical adapter. This takes the coil from the asa from the middle of the gun into the front of the gun where the front foregrip is. This allows someone to either screw a tank vertically or to add an expanison chamber or regulator replacing the front foregrip and improving gun performance.

The pro team products bolt. This bolt had numerous holes on the outside of the bole versus one large open hole. This gives the gun a more consistent shot everytime and a more consistent backspin.

The tippmann 98 custom rt. This makes the gun into an reactive trigger. It makes the trigger so that you can pull the trigger back without having to let it go foward again. It bounces the trigger back and forth making the gun shooting around 9 balls per second.

The tippmann 98 adjustable stock. This provides as a stock on the back of a tippmann as well as an rear veloctiy adjuster. If it were me though i would prefer not to have a stock. I think they just make you bulky if your not strictly a sniper

This is the tippmann 98 and 98 custom low pressure kit. This kit is from tippmann themselves. The description of this kit comes directly from tippmann.Due to the growing demand for Nitrogen/Compressed Air systems we decided to develop a kit that would offer the best efficiency at a set low pressure. Although the stock 98 Custom will operate on nitrogen without the kit, there is very little advantage over CO2 because the internals are not designed for a high pressure system. When we design a gun to operate on CO2 we have to take into consideration a large variety of pressures ranging from an empty bottle all the way up to 3,000psi, where the rupture disc fails. CO2 changes pressure as the temperature changes, the higher the temperature the higher the pressure. Granted we cannot cover the entire pressure range, so we shoot for the most common operating pressures. These pressures are 300-2,000psi. In order to have a gun function through this pressure range, without a large velocity variation, we sacrifice some efficiency and overall gun comfort. With a high pressure system we are only working with one set operating pressure. Through research and testing we have found the most efficient pressure to be between 300-400psi. By changing the configuration of the valve and rear bolt we can obtain better efficiency, less recoil, and a more consistent shot to shot velocity. The new HP kit consists of a lighter rear bolt, new rear cocking assembly, lighter drive spring, new valve assembly, new vertical adapter, and a low pressure chamber. With the operating pressure around 350psi the valve opens much easier, but also requires a larger amount of gas flow to maintain ball velocity. Along with the valve modifications the low pressure chamber supports these flow and volume demands.A nitrogen bottle and secondary regulator are not included in this kit, but are required. The Low Pressure System is available for the 98 Custom and the Model 98.

A-5 upgrades

This is the tippmann a-5 rt. This is the same thing as the 98 custom rt except that it is alot fsater than the 98 rt. This shoots at least twice as fast.

The egrip frame from tippmann. The E-grip system uses an electronic control board to activate a solenoid. When activated, the solenoid disengagesthe sear, which in turn fires the marker. The system is powered by a 9 volt battery. All electronic components are completely contained inside the grip, which allow you to quickly and easily change grips

Due to the fact that there are very few a-5 parts and many 98 custom parts i chose the ones that i found to be most important. If there is a part that you may see elsewhere and would like to know more about email us at  teamblackstatic@yahoo.com