Paramètres related to :

Paramètres related to :

Spindle control.

Symbol		Param	Bit		Description
GST	0003		5	1= Gear shift by SOR signal; 0= Orientation By SOR.
TCW	0013		7	Output code at S analog output.
CWM	0013		6	Output code at S analog output.
ORCW	0013		5	1= Minus analog output at orientation; 0= Plus output.
SFOUT	0020		7	SF in S4/5 is : 1= output at new; 0= Output at gear change.
SCTO	0024		2	1= Spindle speed reach signal is checked.
PSG2	0028		7	Gear ratio of spindle and position coder.
PSG1	0028		6	Gear ratio of spindle and position coder.
SFOB	0029		5	In CSS mode : 1= SF is output; 0= SF is not output.
LGCM	0035		6	1= Low, Highspeed gear change depend on param. No. 585.
SPMRPM	0063		7	1= At S5 Digit anal. Control, Max Spdl speed i 99999R.
SPLOW	0108			Min. Spindle speed during CSS or at gear change.
SCTTIM	0110			Set delay timer for checking the Spndl speed reach signal.
PSANGN	0516			Gain of D/A converter for spindle analog output.
GRHMAX	0539			Max. spndl speed (for anal. Output) at high gear.
GRHMIN	0540			Lower limit of spndl speed when using high speed gear.
GRLMAX	0541			Max. spndl speed at lower speed gear.
SPDMAX	0542			Upper limit of output value to the spindle motor.
SPDMIN	0543			Lower limit of output value to the spindle motor.
LOWSP	0551			Min. spindle speed in constant Surface speed control mode.
GRTMAX	0555			Max. Spindle speed at high speed gear in 3 step gear select.
GRTMIN	0556			Lower limit of spindle speed when using high speed gear.
SPDLC	0577			Zero offset value of the spindle analog output.
SPDMXL	0585			Spindle speed at which gear is changed (L to H or L to M).
SPDMXH	0586			Spindle speed at which gear is changed (M to H).
PSANGS	7516			Gain of D/A converter for sub-spindle analog output.
SPDLCS	7539			Zero offset of the sub-spindle analog output.

Spindle control.

Symbol

Description

GST

1= Gear shift by SOR signal; 0= Orientation By SOR.

TCW

Output code at S analog output.

CWM

Output code at S analog output.

ORCW

1= Minus analog output at orientation; 0= Plus output.

SFOUT

SF in S4/5 is : 1= output at new; 0= Output at gear change.

SCTO

1= Spindle speed reach signal is checked.

PSG2

Gear ratio of spindle and position coder.

PSG1

Gear ratio of spindle and position coder.

SFOB

In CSS mode : 1= SF is output; 0= SF is not output.

LGCM

1= Low, Highspeed gear change depend on param. No. 585.

SPMRPM

1= At S5 Digit anal. Control, Max Spdl speed i 99999R.

SPLOW

Min. Spindle speed during CSS or at gear change.

SCTTIM

Set delay timer for checking the Spndl speed reach signal.

PSANGN

Gain of D/A converter for spindle analog output.

GRHMAX

Max. spndl speed (for anal. Output) at high gear.

GRHMIN

Lower limit of spndl speed when using high speed gear.

GRLMAX

Max. spndl speed at lower speed gear.

SPDMAX

Upper limit of output value to the spindle motor.

SPDMIN

Lower limit of output value to the spindle motor.

LOWSP

Min. spindle speed in constant Surface speed control mode.

GRTMAX

Max. Spindle speed at high speed gear in 3 step gear select.

GRTMIN

Lower limit of spindle speed when using high speed gear.

SPDLC

Zero offset value of the spindle analog output.

SPDMXL

Spindle speed at which gear is changed (L to H or L to M).

SPDMXH

Spindle speed at which gear is changed (M to H).

PSANGS

Gain of D/A converter for sub-spindle analog output.

SPDLCS

Zero offset of the sub-spindle analog output.